ATM_ID: 3842725C-7590-1014-8825-B20C57619FB6

MFF:

PLANNEDTIMESTAFF:

ID: DPQA_Regression_Connectivity/Testcases/FS_55.003_Direct_connectivity/84447

TESTCASE_HEADLINE: To set HTTP/1.1 over USB bit.

GROUP:

FEATURE:

SUB_FEATURE:

INPUT: 1.  Direct printing through driver should be enabled on the device (WebUI-Properties-Connectivity-setup-USB connection mode-Check "Direct Printing via driver". 
<P>2. Connect the USB type B port to any of the USB card slot in the Mac PC  and with the working MFD. Using the mac client debug console, identify the port number to which the USB type B port is connected to the MFD.
--------------------------  
Steps to find the port number from debug log monitor:
Request/Response on multiple interfaces: 
 <P>1.sudo defaults write configd com.apple.ippusb.loglevel 2;
<P>2. sudo defaults write configd com.apple.ippusbd.loglevel 2;
<P>3. sudo sudo sed -i .ORIG 's/\\[<= Level notice\\]/[<= Level debug]/' /etc/asl.conf
<P>4. sudo killall -HUP syslog
 <P>5. sudo syslog -F std.4 -w -k Sender configd -o -k Sender ippusbd
----------------------------
<P>3.  IPP should be enabled on the device.
<P>4. Airprint should be enabled on the device.
<P>5. Perform an IPP print job with the help of the below command:
<P> ipptool -tv -f print-job.test ipp://localhost:port #/ipp/print print-job.test\
Note: Port Number may differ based on the Mac port that is connected with the device."

PROCEDURE: 1. Open the device webpage with its valid IP.
<P>2. Verify whether the device webpage is accessible.
<P>3. Verify the debug logging monitor logs for the HTTP sevice support.

OUTPUT: Device webpage should be accessible over HTTP/1.1 
<P>2. Debug logging monitor logs should possess the information about the HTTP service support.

PROCESS:

PRIORITY:

TEST_TYPE:

LOE:

RESOURCE_HW:

RESOURCE_CONSUMEABLES:

RESOURCE_MEDIA:

SKILL_SET:

TEST_CASE_TYPE:

TESTCASE_SOURCE:

SPEC: FS 55.003 Direct Connectivity

SPEC_VERSION: 1.0027999999999999

SPEC_TAG: [55.003.031] (FT-17796) [D3.6 - *]The implemented HTTP service shall have defined capabilities:
[55.003.031.001] (FT-17796) [D3.6 - *] The HTTP service shall set the “Any HTTP/1.1 over USB bit in the Device Info descriptor,  to tell the host that the device supports this..

ATM_OWNER:

APPROVE_QE:

APPROVED_QE:

APPROVE_SE:

APPROVED_SE:

APPROVE_SPAR:

APPROVED_SPAR:

ASSOCIATED_TESTCASES:

TRAINING:

TESTCASE_VERSION:

TESTCASE_STATE:

TESTCASE_PLATFORM:

TESTCASE_PRODUCT:

TESTCASE_APPROVALS:

CDATE: 1478590916

MDATE: 1478590916, 1478594525, 1483518522, 1501222461

MUSER: q3sjpj97, q3sjpj97, q3sjpj97, w3K3WRKH

AUTHOR: q3sjpj97

ATM_MCOMMENTS: Imported from spreadsheet, Requirement Mapping, Renamed from "DPQA_NewFeature/D3.6/FT-16947_R1214-05-Airprint_IPP_USB_Test_cases/84447"., Renamed from "DPQA_Regression_Connectivity/Testcases/FS_55.003_Direct_connectivity/_FT-16947_R1214-05-Airprint_IPP_USB_Test_cases/84447".

HISTORY:

ATM_LOCKED:

ATM_REQLINK: 59EA5B4C-7B26-1014-B839-8124A0BF9085

ATM_REQCOUNT: 1

QA_TEAM:

TC_WEIGHTAGE:

FILENAME:

FILEDESC:

FILES: