ATM_ID: AD02B970-89A8-11E8-8689-6E3695B419BA

MFF:

PLANNEDTIMESTAFF:

ID: DPQA_Regression_Connectivity/Testcases/FS_55.050_Wireless_Connectivity/112071

TESTCASE_HEADLINE: To verify that Xerox Wireless adapter shall support the 5 GHz frequency band and its below Wi-Fi modes:
• IEEE 802.11a
• IEEE 802.11n
• IEEE 802.11ac
• Mixed mode

(Validation from LUI)

GROUP:

FEATURE:

SUB_FEATURE:

INPUT: <p></p>
<ol><li value="1">Test requires a active Router/AP and Xerox Wireless USB Adapter which supports 2.4 GHz and 5 GHz frequency bands and Wi-Fi modes (Edimax EW-7822ULC - AC1200 Wireless Dual-Band USB 3.0 Adapter). <br />
</li><li value="2">Confirm rear USB ports are enabled.</li></ol>

PROCEDURE: <p></p>
<ol><li value="1">Do the below configurations In Router/AP and save the changes <br />
<br />
• Give two different names for 2.4 GHz and 5 GHz frequency bands (i.e. ASUS-2G and ASUS-5G)<br />
• Configure the Router's/AP's Wi-Fi mode as IEEE 802.11a.<br />
• Configure the Router's/AP's frequency band as 5 GHz.<br />
<br />
</li><li value="2">Insert the Xerox Wireless USB Adapter (which supports 2.4 GHz and 5 GHz frequency bands and Wi-Fi modes) into the MFD's rear USB port.<br />
</li><li value="3">LUI will display a pop up that prompts the user to select either "Continue wireless install" or "Skip wireless setup".<br />
</li><li value="4">Click on "Continue wireless install" which will display the available networks.<br />
</li><li value="5">Select the SSID of the corresponding wireless AP ((i.e. ASUS-5G ) and enter the valid configurations (which should match the configurations applied in router and server) and save the changes by clicking on "Done" button. <br />
</li><li value="6">Join the network and Fetch the device new IP address from LUI or console and access the device CWIS using the new IP.<br />
</li><li value="7">Check whether the CWIS is accessible and communicating properly in 5 GHz frequency with IEEE 802.11a mode and Send a print job to confirm connection.<br />
</li><li value="8">Remove the Xerox Wireless USB Adapter Switch the device back to wired and Reconfigure the Router's/AP's Wi-Fi mode as IEEE 802.11n for 5 GHz frequency band and repeat step 2-7.<br />
</li><li value="9">Check whether the CWIS is accessible and communicating properly in 5 GHz frequency with IEEE 802.11n mode.<br />
and Send a print job to confirm the connection.<br />
</li><li value="10">Remove the Xerox Wireless USB Adapter Switch the device back to wired and Reconfigure the Router's/AP's Wi-Fi mode as IEEE 802.11ac for 5 GHz frequency band and repeat step 2-7.<br />
</li><li value="11">Check whether the CWIS is accessible and communicating properly in 5 GHz frequency with IEEE 802.11ac mode and Send a print job to confirm connection.<br />
</li><li value="12">Remove the Xerox Wireless USB Adapter Switch the device back to wired and Reconfigure the Router's/AP's Wi-Fi mode as Mixed Mode for 5 GHz frequency band and repeat step 2-7.<br />
</li><li value="13">Check whether the CWIS is accessible and communicating properly in 5 GHz frequency mixed mode and Send a print job to confirm connection.</li></ol>

OUTPUT: <p></p>
<ol><li value="1">Xerox Wireless USB Adapter (which supports 2.4 GHz and 5 GHz frequency bands and Wi-Fi modes) should be recognized by MFD in STEP 2.<br />
</li><li value="2">CWIS should be accessible and should communicate properly in 5 GHz frequency with IEEE 802.11a mode and job should be printed successfully in STEP 7.<br />
</li><li value="3">CWIS should be accessible and should communicate properly in 5 GHz frequency with IEEE 802.11n mode and job should be printed successfully in STEP 9.<br />
</li><li value="4">CWIS should be accessible and should communicate properly in 5 GHz frequency with IEEE 802.11ac mode and job should be printed successfully in STEP 11.<br />
</li><li value="5">CWIS should be accessible and should communicate properly in 5 GHz frequency mixed mode and job should be printed successfully in STEP 13.</li></ol>

PROCESS:

PRIORITY:

TEST_TYPE:

LOE:

RESOURCE_HW:

RESOURCE_CONSUMEABLES:

RESOURCE_MEDIA:

SKILL_SET:

TEST_CASE_TYPE:

TESTCASE_SOURCE:

SPEC: 55.050 Wireless Connectivity

SPEC_VERSION: 1.0032000000000001

SPEC_TAG: [55.050.110] (FT-21767) [D4.0M - *] The Xerox Wireless adapter shall support the following frequency bands and Wi-Fi modes:
• [55.050.110.02] (FT-21767) [D4.0M - *]  5 GHz (5.150 - 5.825 GHz):
o [55.050.110.02.01] (FT-21767) [D4.0M - *] IEEE 802.11a 
o [55.050.110.02.02] (FT-21767) [D4.0M - *] IEEE 802.11n
o [55.050.110.02.03] (FT-21767) [D4.0M - *] IEEE 802.11ac
o [55.050.110.02.04] (FT-21767) [D4.0M - *] Mixed mode
55.050.004.02 [FT-24078]
[D4.0M - *] The Device shall support the Edimax EW-7822ULC - AC1200 Wireless Dual-Band USB 2.0 Adapter.

ATM_OWNER:

APPROVE_QE:

APPROVED_QE:

APPROVE_SE:

APPROVED_SE:

APPROVE_SPAR:

APPROVED_SPAR:

ASSOCIATED_TESTCASES:

TRAINING:

TESTCASE_VERSION:

TESTCASE_STATE:

TESTCASE_PLATFORM:

TESTCASE_PRODUCT:

TESTCASE_APPROVALS:

CDATE: 1531821818

MDATE: 1531821818, 1538567607

MUSER: q4BVX0J1, q4BVX0J1

AUTHOR: q4BVX0J1

ATM_MCOMMENTS: Imported from spreadsheet, Renamed from "DPQA_NewFeature/LIP_1.0/FT-24078_Update_FS_55.050_Wireless_spec_with_new_KiskaCorvo_WiFi_dongle_info/112071".

HISTORY:

ATM_LOCKED:

ATM_REQLINK: 4035A80A-C920-11E7-A8DD-46D2A5FB8F22, 404E0CB0-C920-11E7-A8DD-46D2A5FB8F22, 4050C9C8-C920-11E7-A8DD-46D2A5FB8F22, 4054A0CA-C920-11E7-A8DD-46D2A5FB8F22, 40568A20-C920-11E7-A8DD-46D2A5FB8F22, 4058ECC0-C920-11E7-A8DD-46D2A5FB8F22, B2813AB2-7F70-11E8-B2D9-6F1396B419BA

ATM_REQCOUNT: 7

QA_TEAM:

TC_WEIGHTAGE:

FILENAME:

FILEDESC:

FILES: