ATM_ID: 328DDBBF-773B-1014-A336-D8A70057191D

MFF:

PLANNEDTIMESTAFF:

ID: DPQA_Workflow_v2/Scan_To../52299

TESTCASE_HEADLINE: �[Case :-Scan To Case 1]�

GROUP:

FEATURE:

SUB_FEATURE:

INPUT: The device under test should be loaded with latest software. All the possile parameters should be configured using the assigned interface (CWIS,LUI or SNMP) Set "Default Walkup Screen" and "Default Screen when Originals are Detected" as "Scan-To"

PROCEDURE:  [Common Settings-Wired-Smartcard-Local-JBA-IPV4] 
 [Template Configuration-Scan To Service] 
 [Filing Protocol-Scan To-SMB - Do not file with Kerberos Ticket] 
 [Filing Policy-Overwrite Existing File] 
 [Filing Address-IPV4] 
 [XSM Enablement-Enabled] 
 [Job Log(.XST)-Enabled] 
 [Confirmation Sheet-Enabled] 
 [Login Credentials-System credentials] 
 [File Format-TIFF 1 file per page] 
 [OutputColor-Auto Detect] 
 [2 Sided Scanning-1 Sided] 
 [Lighten/Darken--3] 
 [Sharpness-0] 
 [Contrast-Manual Contrast 0] 
 [Background Suppression-Off] 
 [Resolution-72] 
 [File SizeQuality-0] 
 [Remove Blank Pages-OFF] 
 [Scan to Original Type-Text] 
 [How Original was produced-Solid Ink Original] 
 [Original Orientation-Upright Images] 
 [Edge Erase-Top] 
 [Build Job-OFF] 
 [Original Size input-Auto] 
 [Rotation Method-Use Device] 
 [Mode of Input-DADH] , [11.238.004] (FT-14212) The expected output for scan services shall be as shown in Table 4., [25.000.002] (FT-14212) The System shall support the following three ORIGINAL ? SCANNED OUTPUT sides imaged selections:, [25.000.002.1] (FT-14212) Simplex scanning;, [25.000.016] (FT-14212) The factory default selection for sides imaged is “1?1”., [11.235.001] (FT-14212) The control shall have 7 levels: -3%2c -2%2c -1%2c 0%2c 1%2c 2%2c 3 where -3 will be the darkest and 3 will be the lightest setting., [11.241.001] (FT-14212) For all services supported the control will have 5 levels: -2 to 2%2c where -2 will be the lowest sharpness (least sharp) and 2 will be the highest sharpness (sharpest)., [11.236.001] (FT-14212) The Manual Contrast control shall have 5 levels: -2%2c -1%2c 0%2c 1%2c 2%2c where -2 will be the lowest and 2 will be the highest contrast., [11.237.002] (FT-14212) The Original Type/Subtype selections that will be available for all scan services (Scan to email%2c Network Scan%2c I-FAX) are listed in Table 2., [46.200.200.1] (FT-14212) PRINT: A Confirmation Sheet shall be printed ., [19.260.004] (FT-14212) CCSFEAT334 Four mutually exclusive Input Image Portrait/Landscape Orientation (IIPLO) options shall be available from which the user may make a single selection: Portrait%2c Landscape%2c Auto: Head to Top and Auto: Head to Feed-edge., [46.200.188] (FT-14212) [D2.2-*] The SA shall have the ability to enable/disable XSM Subdirectory setting for each system file respository via the WebUI, [19.044.001] (FT-14212) It shall be possible to set the amount to be erased from each edge (top%2c bottom%2c left & right) independently., [46.200.142.5] (FT-14212) OVERWRITE: Overwrites existing files with new documents ., [28.010.001] (FT-14212) CCSFEAT10478 The Build Job enable/disable shall be available to the user for supported services on the Local UI., [46.200.028.3] (FT-14212) SMB via NetBIOS over TCP/IP, [28.080.020] (FT-14212) CCSFEAT1224 The factory default for Original Size Input shall be “Auto Detect”. , CCSFEAT9347 The device shall support Job Based Accounting API version 4.0.5., CCSFEAT13845 [D2.2-*] When JBA is enabled%2c all JBA supported job types shall be tracked as records in the JBA job log regardless of prompting enablement., CCSFEAT8878 End users will be provided with a method of accessing and using the Job-based Accounting data from a client application that performs accounting tasks with data gathered from the System Device (or devices)., CCSFEAT8881 A System Device will communicate with the External Accounting System via its network connection, CCSFEAT8890.12 Job’s number of copies completed (number of sets), CCSFEAT14932 At the request of the SA the audit log shall be downloaded to the SA client PC via the webUI, CCSFEAT14932 At the request of the SA the audit log shall be downloaded to the SA client PC via the webUI, Event Id:-105%2c62%2c94%2c49%2c144%2c145%2c6%2c29%2c30%2c42 CCSFEAT21254 The audit log entry data shall report events contained in table 1 below:, CCSFEAT3665 The system shall restrict the audit log access to the SA, CCSFEAT3666 The SA shall need to enter his user name & password to be able to access the audit log feature, [44.001.242] (FT-14212) [D1.7-*] The SA shall be able to create a customer defined permission role, [44.001.243] (FT-14212) [D1.7-*] The SA shall be able to view all customer defined permission roles created on the device, [44.001.025] (FT-14212) [D1.7-*] The SA shall be able to modify a customer defined role’s, [44.001.025.1] (FT-14212) [D1.7-*] Role Profile (name and description), [44.001.025.2] (FT-14212) [D1.7-*] Role Permissions, [44.001.025.3] (FT-14212) [D1.7-*] User/Group Mappings, [44.001.229] (FT-14212) [D2.2-*] The SA shall be able to create a role for only the individually selected Local User or Groups., [44.001.029] (FT-14212) [D1.7-*] The SA shall be able to associate an existing local user to an existing role., [44.060.001] (FT-14212) CCSFEAT4614 [D1.3-*] The device shall support at least the following smart cards:, [44.060.001.11] (FT-14212) .NET, [44.060.002] (FT-14212) [D1.9-*] Other cards may be supported in addition to this list. A message will be displayed to the user if an unsupported card type is used., [44.060.003] (FT-14212) [D1.9-*] The following smart cards are not supported and will trigger an unsupported card error message to the walk up user. Other cards may also trigger this message., [44.060.003.1] (FT-14212) .1 [D1.9-D2.2] Gemalto .NET v1, [44.060.004] (FT-14212) CCSFEAT4615 [D1.3-*] The device shall support any USB CCID compliant card readers%2c but the following shall be validated:, [44.060.004.6] (FT-14212) OmniKey Cardman 3021 USB, [44.060.005] (FT-14212) [D1.3-*] When the Card Reader is plugged into the USB port of the system AND Smartcard support is enabled%2c a pop-up window shall appear on the LUI indicating that the device detected the card reader., [44.060.006] (FT-14212) [D1.3-*] If the system properly configured the device to use the card reader%2c then the pop-up shall indicate that the reader is ready to be used., [44.060.007] (FT-14212) [D1.3-*] If the system could not properly configure the card reader for use than there shall be no pop-up., [44.060.008] (FT-14212) [D1.3-*] The pop-up window shall have a Close button that will remove the window from the LUI., [44.060.009] (FT-14212) [D1.3-*] Once the card reader has been properly configured%2c if the reader is removed from the USB Port AND Smartcard support is enabled%2c then a pop-up shall appear on the LUI indicating that the card reader has been unplugged., [44.060.0010] (FT-14212) [D1.3-*] The device shall be able to differentiate between USB devices%2c and thus will not display the pop-up unless it is for a Card Reader., [46.050.014] (FT-14212) CCSFEAT17321 File Format and File Options, [46.050.007] (FT-14212) CCSFEAT17319 The user shall be allowed to set the Darkness value between three steps below nominal (0) and three steps above nominal (0) in increments of one step where steps below nominal represent a lighter image and steps above nominal represent a darker image., [46.050.070] (FT-14212) CCSFEAT17390 The user shall be allowed to set the Sharpness value between two steps below nominal (0) and two steps above nominal (0) in increments of one step where steps below nominal represent a softer image and steps above nominal represent a sharper image., [46.050.006] (FT-14212) CCSFEAT17318 The user shall be allowed to select either auto-contrast adjustment or manually set the Contrast value between two steps below nominal (0) and two steps above nominal (0) in increments of one step where steps below nominal represent less Contrast and steps above nominal represent more Contrast., [46.050.003] (FT-14212) CCSFEAT17315 The supported Auto Background Suppression values are the following:, [46.050.062] (FT-14212) CCSFEAT17366 [-Ll] If Original Type is set to Newspaper/Magazine then Auto Background Suppression shall be ON as default., [46.050.068] (FT-14212) CCSFEAT17388 The supported Resolution values are the following:, [46.050.005] (FT-14212) CCSFEAT17317 The supported Quality/File Size values are a 3-step range with an integer range of 0-255 and the following incremented steps:255%2c 128%2c 0, [46.050.073] (FT-14212) CCSFEAT17393 [+D2.2] The supported Blank Page Management settings are the following:
• Removal All Blank Pages – The scan services shall attempt to detect and remove any blank images
• Include All Blank Pages – The scan service shall not remove any blank im
, [46.050.058] (FT-14212) CCSFEAT17363 The supported Original Type attribute values are the following:, [46.050.060] (FT-14212) CCSFEAT17365 The supported Original SubType attribute values are the following:, [46.050.057] (FT-14212) CCSFEAT17362 The supported Input Orientation values are the following:, [46.050.032] (FT-14212) CCSFEAT17338 If Edge to Edge Scanning is enabled and the user sets an Input Edge Erase value%2c the Edge to Edge Scanning shall be disabled., [46.050.030] (FT-14212) CCSFEAT17336 If an input document is 2 Sided%2c Edge Erase values set for Side 1 of the document shall be ‘mirrored’ over the x-axis for Side 2 as follows: 
• Side 2 TOP = Side 1 TOP
• Side 2 BOTTOM = Side 1 BOTTOM
• Side 2 LEFT = Side 1 RIGHT
• Side 2 RIGHT = Side 1 LEFT. 
, [46.050.028] (FT-14212) CCSFEAT17335 The supported Input Edge Erase values are the following:, [46.050.036] (FT-14212) CCSFEAT17341 supported Input Media Size values are the following: Please note some sizes may only be supported though the ADF or only from the Platen -- this list of presets for Scan to X (Mail%2c file etc) may not be equal to those available for Copy), [46.050.075] (FT-14212) CCSFEAT17411 [+D2.2] The supported TIFF Rotation Method settings are the following:, [46.050.037] (FT-14212) CCSFEAT17342 A remote interface (Web%2c MIB) user shall be allowed to manually define an Input Size Manual where the minimum fast scan dimension is the smaller of the device specific Platen and DADH minimum fast scan directions.

OUTPUT: All the input settings should be configurable and the scan to job should complete successfully. Validate that all the configured parameters are reflecting in the output, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , 

PROCESS:

PRIORITY:

TEST_TYPE:

LOE:

RESOURCE_HW:

RESOURCE_CONSUMEABLES:

RESOURCE_MEDIA:

SKILL_SET:

TEST_CASE_TYPE:

TESTCASE_SOURCE:

SPEC:

SPEC_VERSION:

SPEC_TAG:

ATM_OWNER:

APPROVE_QE:

APPROVED_QE:

APPROVE_SE:

APPROVED_SE:

APPROVE_SPAR:

APPROVED_SPAR:

ASSOCIATED_TESTCASES:

TRAINING:

TESTCASE_VERSION:

TESTCASE_STATE:

TESTCASE_PLATFORM:

TESTCASE_PRODUCT:

TESTCASE_APPROVALS:

CDATE: 1458183887

MDATE: 1458183887

MUSER: w4939RDM

AUTHOR: w4939RDM

ATM_MCOMMENTS: Imported from CSV

HISTORY:

ATM_LOCKED:

ATM_REQLINK: D5D7B096-6EAC-1014-836C-B68CBAA491EA, D5FB1C00-6EAC-1014-AF69-DDEBBA7F80E0, D62904DE-6EAC-1014-931B-CF7044612E95, D62B7A07-6EAC-1014-9AE5-E9B89D9FD662, D62DECBC-6EAC-1014-9B03-C1C11345BFC1, D6420D6C-6EAC-1014-9673-EAC21695B5D1, D644ABC3-6EAC-1014-A4C6-E78DC4B66348, D6471532-6EAC-1014-8A44-D78D5517D5B0, D64BF763-6EAC-1014-8EA1-C92CAB7389F7, A1558B79-6FAB-1014-A0D8-B468BD92E37F, A158488E-6FAB-1014-9AB1-B6D4A04B6E7F, E50D056B-6E6F-1014-B5F8-A4645CB2B43E, E5101395-6E6F-1014-8917-C6375387D3B3, E51312D4-6E6F-1014-B013-93E165E85025, E51BA0FC-6E6F-1014-A9BB-8EE47872C546, E5DEE9C3-6E6F-1014-81BF-ED83C2696191, A99B9656-6E71-1014-93C8-97E245C02EC1, A99EDC98-6E71-1014-974B-D03B96C9C003, A9C97516-6E71-1014-8FF3-E5AD8A928663, B1C4BF5B-850E-1014-82EC-FA69492ADD4A, EA01BE6E-6E18-1014-AB24-851D5D90F66B, EA0466A9-6E18-1014-903A-EF852E30F816, EA06E60A-6E18-1014-83E9-D9E14A1CEB41, EA10B739-6E18-1014-AEFB-B8251C518206, 4143F78B-6EB0-1014-9478-BE9FE645644F, 4146A2F1-6EB0-1014-B208-8BB5A2E93480, 41932766-6EB0-1014-8BFC-B5D0591256B9, 41FC68CD-6EB0-1014-B223-E3C85E183F01, 41FEA330-6EB0-1014-9318-C17685A65876, 296AC6D3-6E6C-1014-8F6E-E7E1106E3F83, A031B4B9-6FC8-1014-BD6C-DE6C3C3BE627, 446631C8-70B7-1014-A741-BC37E7F15FA7, F60EF7D5-6E5F-1014-B064-BD62948A4605, F6599B03-6E5F-1014-98E2-F2014E65519D, 8D02C2CD-7675-1014-9785-8BE85C1C4074, 8A569E05-875D-1014-8D17-C4E84E76DA6E, 61E7F74C-6FAF-1014-B083-D8863455867D, 61F04CFC-6FAF-1014-9E8A-F036BDFA1E63, 61F34B4B-6FAF-1014-9A87-B1E186865421, 61F6610B-6FAF-1014-A3E3-AE1773E66902, 62199469-6FAF-1014-8999-B08C1E9E961C, 6246A499-6FAF-1014-918B-FA32642BF927, 624CCA0E-6FAF-1014-8222-9C26B5F3D8BA, 62530F4D-6FAF-1014-93EF-E29AC38EDAC5, 625FD4F0-6FAF-1014-B357-B16040FE3B92, 62625103-6FAF-1014-8348-F8C42D62A944, 62986991-6FAF-1014-93FF-C2F65F004418, 629B1B19-6FAF-1014-B886-E88490BBA6C9, 62A0CFBB-6FAF-1014-AE2D-F183DDA21456, 62A5BABB-6FAF-1014-8477-DF7F588561BE, 62B4E30E-6FAF-1014-819F-D23AD7A7AC68, 62BC5334-6FAF-1014-887E-E16A76A0C041, 62C6FB16-6FAF-1014-AE68-BF7DA38DAAA6, 62CC8482-6FAF-1014-8458-BBF0255E4A1B, 191A36D9-70EF-1014-8F6C-A8A3BE8EB60D, 1BA00745-70EF-1014-9A2E-D5B21071E422, 1C55A317-70EF-1014-8335-A581FB63881C, 1CA16316-70EF-1014-A93B-BD8CC4783FCE

ATM_REQCOUNT: 58

QA_TEAM:

TC_WEIGHTAGE:

FILENAME:

FILEDESC:

FILES: