ATM_ID: 685FFC30-6FA7-1014-8BD7-A953F4223688 MFF: PLANNEDTIMESTAFF: ID: DPQA_Workflow_v2/Scan_to_file/50080 TESTCASE_HEADLINE: [Use Case-Case 28] GROUP: FEATURE: SUB_FEATURE: INPUT: The device under test should be loaded with latest software. All the possile parameters should be configured using the assigned interface (CWIS,LUI or SNMP) PROCEDURE: [Common Settings-Wired-Smartcard-Local-JBA-IPV4] [Template Configuration-Enter scan Destination Template] [Filing Protocol-Scan to File - FTP] [Filing Policy-Do not Save] [Filing Address-IPV6] [XSM Enablement-Enabled] [Job Log(.XST)-Enabled] [Confirmation Sheet-Enabled] [Login Credentials-System/Stored in Template or Device] [File Format-PDF Multi Page Image only] [OutputColor-Auto Detect] [2 Sided Scanning-2 Sided] [Lighten/Darken--3] [Sharpness--3] [Contrast-Manual Contrast -2] [Background Suppression-Auto Suppression] [Resolution-100] [File SizeQuality-1] [Remove Blank Pages-OFF] [Scan to Original Type-Map] [How Original was produced-Not Applicable] [Original Orientation-Landscape Originals] [Edge Erase-Top] [Build Job-OFF] [Original Size input-Custom Size] [Rotation Method-Not Applicable] [Mode of Input-Platern] , [44.060.0010] (FT-14212) [D1.3-*] The device shall be able to differentiate between USB devices%2c and thus will not display the pop-up unless it is for a Card Reader. , [44.060.009] (FT-14212) [D1.3-*] Once the card reader has been properly configured%2c if the reader is removed from the USB Port AND Smartcard support is enabled%2c then a pop-up shall appear on the LUI indicating that the card reader has been unplugged. , [44.060.008] (FT-14212) [D1.3-*] The pop-up window shall have a Close button that will remove the window from the LUI., [44.060.007] (FT-14212) [D1.3-*] If the system could not properly configure the card reader for use than there shall be no pop-up. , [44.060.006] (FT-14212) [D1.3-*] If the system properly configured the device to use the card reader%2c then the pop-up shall indicate that the reader is ready to be used. , [44.060.005] (FT-14212) [D1.3-*] When the Card Reader is plugged into the USB port of the system AND Smartcard support is enabled%2c a pop-up window shall appear on the LUI indicating that the device detected the card reader. , [44.060.004.6] (FT-14212) OmniKey Cardman 3021 USB, [44.060.004] (FT-14212) CCSFEAT4615 [D1.3-*] The device shall support any USB CCID compliant card readers%2c but the following shall be validated: , [44.060.003.1] (FT-14212) .1 [D1.9-D2.2] Gemalto .NET v1, [44.060.003] (FT-14212) [D1.9-*] The following smart cards are not supported and will trigger an unsupported card error message to the walk up user. Other cards may also trigger this message. , [44.060.002] (FT-14212) [D1.9-*] Other cards may be supported in addition to this list. A message will be displayed to the user if an unsupported card type is used. , [44.060.001.11] (FT-14212) .NET, [44.060.001] (FT-14212) CCSFEAT4614 [D1.3-*] The device shall support at least the following smart cards: , CCSFEAT3666 The SA shall need to enter his user name & password to be able to access the audit log feature, CCSFEAT3665 The system shall restrict the audit log access to the SA , Event Id:-105%2c62%2c94%2c49%2c144%2c145%2c6%2c29%2c30%2c42 CCSFEAT21254 The audit log entry data shall report events contained in table 1 below: , CCSFEAT14932 At the request of the SA the audit log shall be downloaded to the SA client PC via the webUI, CCSFEAT14932 At the request of the SA the audit log shall be downloaded to the SA client PC via the webUI, [18.050.015] CCSFEAT8890 Job Attributes used with Job-based Accounting., CCSFEAT8878 End users will be provided with a method of accessing and using the Job-based Accounting data from a client application that performs accounting tasks with data gathered from the System Device (or devices). , CCSFEAT13845 [D2.2-*] When JBA is enabled%2c all JBA supported job types shall be tracked as records in the JBA job log regardless of prompting enablement. , CCSFEAT9347 The device shall support Job Based Accounting API version 4.0.5., [46.200.198.3] (FT-14212) CCSFEAT8495.3 errors only’ - confirmation sheet shall be printed for scan to file jobs only in case of errors. , [46.200.200.1] (FT-14212) PRINT: A Confirmation Sheet shall be printed ., [46.200.200] (FT-14212) The supported Confirmation Method values are the following: , [46.200.218.5] (FT-14212) System , [44.001.029] (FT-14212) [D1.7-*] The SA shall be able to associate an existing local user to an existing role., [44.001.229] (FT-14212) [D2.2-*] The SA shall be able to create a role for only the individually selected Local User or Groups. , [44.001.025.3] (FT-14212) [D1.7-*] User/Group Mappings, [44.001.025.2] (FT-14212) [D1.7-*] Role Permissions, [44.001.025.1] (FT-14212) [D1.7-*] Role Profile (name and description), [44.001.025] (FT-14212) [D1.7-*] The SA shall be able to modify a customer defined role’s, [44.001.243] (FT-14212) [D1.7-*] The SA shall be able to view all customer defined permission roles created on the device.Modify Role , [44.001.242] (FT-14212) [D1.7-*] The SA shall be able to create a customer defined permission role, [46.050.072] (FT-14212) CCSFEAT17392 The supported Sides To Scan values are the following: 1. ONE_SIDED: The scan service shall only scan one side of each page of the input document . 2. TWO_SIDED: The scan service shall scan both sides of each page of the input document. 3. SECOND_SIDE_ROTATION: The scan service shall scan both sides of each page of the input document and shall apply a 180 degree rotation to the second side image., [46.050.007] (FT-14212) CCSFEAT17319 The user shall be allowed to set the Darkness value between three steps below nominal (0) and three steps above nominal (0) in increments of one step where steps below nominal represent a lighter image and steps above nominal represent a darker image. , [46.050.065] (FT-14212) CCSFEAT17385 The supported Output Color values are the following on devices enabled for color scanning: 1. Full Color: Scanned image data is output in 24bit color%2c 8 bits per component. 2. Grayscale: Scanned image data is output in 8bpp grayscale. 3. Black/White: Output will be binary regardless of original color. 4. Auto Color Detect: The output is based on the detection of color on the document. If there is no color%2c the output will generally be Grayscale., Table 18 [46.050.061] (FT-14212) CCSFEAT17367 Original Type/SubType* Defaults for Discovery Solid Ink and Laser Products. , Ref: Table 6 - [46.050.014] (FT-14212) CCSFEAT17321 File Format and File Options , [28.080.001] (FT-14212) CCSFEAT1216 When manually selecting the Original Size Input the user must enter dimensions for both the document process direction dimension (slow-scan dimension) and document inboard-outboard dimension (fast-scan dimension). , [19.044.001] (FT-14212) CCSFEAT1055 It shall be possible to set the amount to be erased from each edge (top%2c bottom%2c left & right) independently. , [28.010.001] (FT-14212) CCSFEAT10478 The Build Job enable/disable shall be available to the user for supported services on the Local UI., [19.260.006] (FT-14212) CCSFEAT336 If the user specifies the IIPLO as “Landscape” all input images in that job-segment shall be considered to be intrinsically landscape in nature%2c and the “up” direction of each input image in that job-segment shall be determined using each original’s Input Paper Feed Orientation (SEF or LEF) and presuming that the original is placed in one of the approved physical orientations%2c such that the “up” direction is towards the longer edge that is in the feed direction or away from the user. , [19.260.004] (FT-14212) CCSFEAT334 Four mutually exclusive Input Image Portrait/Landscape Orientation (IIPLO) options shall be available from which the user may make a single selection: Portrait%2c Landscape%2c Auto: Head to Top and Auto: Head to Feed-edge. , [11.237.002] (FT-14212) The Original Type/Subtype selections that will be available for all scan services (Scan to email%2c Network Scan%2c I-FAX) are listed in Table 2., [11.241.001] (FT-14212) For all services supported the control will have 5 levels: -2 to 2%2c where -2 will be the lowest sharpness (least sharp) and 2 will be the highest sharpness (sharpest). , [11.235.001] (FT-14212) The control shall have 7 levels: -3%2c -2%2c -1%2c 0%2c 1%2c 2%2c 3 where -3 will be the darkest and 3 will be the lightest setting. , [25.000.002.2] (FT-14212) Duplex scanning; , [11.238.004] (FT-14212) CCSFEAT5793 The expected output for scan services shall be as shown in Table 4., [46.200.142.4] (FT-14212) NEW_EXACT: Stores documents with a specific%2c user-defined filename . , [46.200.028.2] (FT-14212) FTP over IP OUTPUT: All the input settings should be configurable and the scan to file job should complete successfully. Validate that all the configured parameters are reflecting in the output, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , PROCESS: PRIORITY: TEST_TYPE: LOE: RESOURCE_HW: RESOURCE_CONSUMEABLES: RESOURCE_MEDIA: SKILL_SET: TEST_CASE_TYPE: TESTCASE_SOURCE: SPEC: SPEC_VERSION: ATM_OWNER: APPROVE_QE: APPROVED_QE: APPROVE_SE: APPROVED_SE: APPROVE_SPAR: APPROVED_SPAR: ASSOCIATED_TESTCASES: TRAINING: TESTCASE_VERSION: TESTCASE_STATE: TESTCASE_PLATFORM: TESTCASE_PRODUCT: TESTCASE_APPROVALS: CDATE: 1457602013 MDATE: 1457602013 MUSER: w4939RDM AUTHOR: w4939RDM ATM_MCOMMENTS: Imported from spreadsheet HISTORY: ATM_LOCKED: ATM_REQLINK: D5D7B096-6EAC-1014-836C-B68CBAA491EA, D5FB1C00-6EAC-1014-AF69-DDEBBA7F80E0, D62904DE-6EAC-1014-931B-CF7044612E95, D62B7A07-6EAC-1014-9AE5-E9B89D9FD662, D62DECBC-6EAC-1014-9B03-C1C11345BFC1, D6420D6C-6EAC-1014-9673-EAC21695B5D1, D644ABC3-6EAC-1014-A4C6-E78DC4B66348, D6471532-6EAC-1014-8A44-D78D5517D5B0, D64BF763-6EAC-1014-8EA1-C92CAB7389F7, A1558B79-6FAB-1014-A0D8-B468BD92E37F, A158488E-6FAB-1014-9AB1-B6D4A04B6E7F, E50D056B-6E6F-1014-B5F8-A4645CB2B43E, E5101395-6E6F-1014-8917-C6375387D3B3, E51312D4-6E6F-1014-B013-93E165E85025, E55F45F8-6E6F-1014-B892-DDDD00130A4D, A99B9656-6E71-1014-93C8-97E245C02EC1, A99EDC98-6E71-1014-974B-D03B96C9C003, A9C97516-6E71-1014-8FF3-E5AD8A928663, B1C4BF5B-850E-1014-82EC-FA69492ADD4A, EA01BE6E-6E18-1014-AB24-851D5D90F66B, EA0466A9-6E18-1014-903A-EF852E30F816, EA06E60A-6E18-1014-83E9-D9E14A1CEB41, EA10B739-6E18-1014-AEFB-B8251C518206, 4143F78B-6EB0-1014-9478-BE9FE645644F, 4146A2F1-6EB0-1014-B208-8BB5A2E93480, 41932766-6EB0-1014-8BFC-B5D0591256B9, 41FC68CD-6EB0-1014-B223-E3C85E183F01, 41FEA330-6EB0-1014-9318-C17685A65876, 296AC6D3-6E6C-1014-8F6E-E7E1106E3F83, A031B4B9-6FC8-1014-BD6C-DE6C3C3BE627, A036FFCC-6FC8-1014-A322-DF5AE32B1B05, F61428B1-6E5F-1014-8BD9-CE4771117B74, 8D02C2CD-7675-1014-9785-8BE85C1C4074, 89E6D151-875D-1014-98D5-E86B4430E29E, 61F6610B-6FAF-1014-A3E3-AE1773E66902, 62199469-6FAF-1014-8999-B08C1E9E961C, 62A364D1-6FAF-1014-9E4F-99CE91F80132, 62AD0A80-6FAF-1014-95B6-F04B89349BFB, 62C4710D-6FAF-1014-AD69-9671E07D0C1C, 19176C35-70EF-1014-A0E5-A27CD9BC9DE3, 1B9D17BA-70EF-1014-8D0E-B3F1E03C5F66, 1C9803D6-70EF-1014-81B4-A5249FF18D79, 1C9EB472-70EF-1014-B6BA-EB50EAE70EA9, 1CA16316-70EF-1014-A93B-BD8CC4783FCE, 1CEA9402-70EF-1014-9BA2-F251B4B14286 ATM_REQCOUNT: 45 QA_TEAM: TC_WEIGHTAGE: FILENAME: FILEDESC: FILES: