ATM_ID: A5B90A52-8227-11E9-802B-234BF6333A5F

ID: PUQE-CFT_Atlantis_2.0-D5.1/FS_22.020_Installation_and_Configuration_Wizard/40740

TESTCASE_HEADLINE: Auto-discovery of Proxy - Case 1 (friendly Xerox machine responded, Connectivity attributes received, Connected to XCLS successfully)

GROUP:

FEATURE:

SUB_FEATURE:

INPUT: 
  1. MFD has wired/wireless network connection.

  2. Bring the MFD to Install Wizard mode using the MITS tool.

  3. Run the Install Wizard until a successful Intranet test i.e.; "Connected to network".

  4. Open the Web UI of the MFD using the IP address displayed in the SR3 region. Go to Properties -- Security -- logs -- Network Troubleshooting; start a session.

  5. Configure the below settings in few other MFDs which belong to the same network as the test MFD.
    i. Go to Web UI -- Properties -- General Setup -- Remote Services; configure a valid HTTP Proxy Server.
    ii. Go to Web UI -- Properties -- Connectivity -- Setup; enable WSD (Web Services on Device).

PROCEDURE: 
  1. In "Auto Acquire Device Profile" screen; when the Internet test is active ("Connecting to Xerox"); wait until the device auto-discovers a proxy server address.

  2. Once the Internet test is successful; stop the Network Troubleshooting log session and download the log file from the Web UI.

  3. Open the logs using the Wireshark application and check the following actions.
      i. The device has called the XCLS server regardless of the presence of a proxy server; and has failed to connect.
      ii. The device has tried to discover friendly machines on the network.
      iii. A friendly machine has responded.
      iv. The device has requested the connectivity attributes (usually the Proxy server address; but also DNS address if null) from the friendly machine.
      v. The device has received the connectivity attributes.
      vi. The device has tried to call the XCLS server again using the new attributes.
      vii. The device has successfully connected to the XCLS server.

  4. Complete the Install Wizard.

  5. Open the Web UI and go to Properties -- General Setup -- Remote Services; check the HTTP Proxy Server settings.

OUTPUT: 
  1. The "Auto Acquire Device Profile" screen on the LUI shall display as "Connecting to Xerox" indicated by a spinning wheel.

  2. The "Auto Acquire Device Profile" screen on the LUI shall display as "Connected to Xerox" indicated by a green check mark.

  3. The logs should show the device trying to auto-discover a proxy server address to connect to the XCLS server.

  4. The device should store the new proxy server address it has obtained from the friendly machine.

PROCESS:

PRIORITY:

TEST_TYPE:

LOE:

RESOURCE_HW:

RESOURCE_CONSUMEABLES:

RESOURCE_MEDIA:

SKILL_SET:

TEST_CASE_TYPE:

TESTCASE_SOURCE:

SPEC: 22.020.205, 22.020.205.001, 22.020.206

SPEC_VERSION: v1.107

SPEC_TAG: [22.020.205] (FT-24594) [D5.1-*] If the call to XCLS fails, immediately the Device shall attempt to discover ‘Friendly’ Xerox machines on the network from which it can obtain the necessary info (usually the Proxy server address, but also DNS address if null) such that it can again attempt this connectivity call to XCLS.  [22.020.205.001] (FT-24594) [D5.1-*]  Upon discovery of Friendly, the Device shall securely request from the Friendly - connectivity attributes (such as Proxy Server and creds and/or DNS).  [22.020.206] (FT-24594) [D5.1-*] If the Device obtains necessary addresses to make an internet call, the Device shall then utilize the connectivity attributes to again attempt the call to the XCLS server. If call to XCLS is successful, it shall store these new connectivity attributes.

ATM_OWNER:

ASSOCIATED_TESTCASES:

TRAINING:

TESTCASE_VERSION:

TESTCASE_STATE:

TESTCASE_PLATFORM:

TESTCASE_PRODUCT:

TESTCASE_APPROVALS:

CDATE: 1559144240

MDATE: 1559144240

MUSER: w4y5hbch

AUTHOR: w4y5hbch

ATM_MCOMMENTS: Imported from spreadsheet

HISTORY:

ATM_LOCKED:

ATM_REQLINK: 5A17FE56-78A3-11E9-98A5-CB618F5C58D9, 5A1A6D9E-78A3-11E9-98A5-CB618F5C58D9, 5A1D1B84-78A3-11E9-98A5-CB618F5C58D9

ATM_REQCOUNT: 3

FILENAME:

FILEDESC:

FILES:

QA_TEAM:

APPROVE_QE:

APPROVED_QE:

APPROVE_SE:

APPROVED_SE:

APPROVE_SPAR:

APPROVED_SPAR:

MFF:

PLANNEDTIMESTAFF:

IMPLEMENTED:

DATA_LOGIC:

AUTOMATABLE_NOTAUTOMATABLE:

TC_WEIGHTAGE: