TEST_TYPE: manual

INPUT: <p></p>
<ol><li value="1">Test requires a active Router/AP and Xerox Wireless USB Adapter which supports 2.4 GHz and 5 GHz frequency bands and Wi-Fi modes.<br />
</li><li value="2">Confirm rear USB ports are enabled.</li></ol>

FILES:

AUTOMATION_GROUP:

AUTOMATABLE: yet_to_be_analyzed

ACTION_TO_BE_DONE:

CONSTRAINTS_DAR: IMP_98: High Level check\
Remarks: \
Owner: Karthika

TESTCASE_MODIFICATION_REQUIRED: no

MFF:

SPEC: FS 55.050 Wireless Connectivity

TESTCASE_FAMILY:

HISTORY:

REASON_FOR_AUTOMATABLE:

CDATE: 1683120867

TESTCASE_APPROVALS:

TESTCASE_STATE:

OUTPUT: <p></p>
<ol><li value="1">Xerox Wireless USB Adapter (which supports 2.4 GHz and 5 GHz frequency bands and Wi-Fi modes) should be recognized by MFD in STEP 2.<br />
</li><li value="2">CWIS should be accessible and should communicate properly in 2.4 GHz frequency with IEEE 802.11b mode and job should be printed successfully in STEP 7.<br />
</li><li value="3">CWIS should be accessible and should communicate properly in 2.4 GHz frequency with IEEE 802.11g mode and job should be printed successfully in STEP 9.<br />
</li><li value="4">CWIS should be accessible and should communicate properly in 2.4 GHz frequency with IEEE 802.11n mode and job should be printed successfully in STEP 11.<br />
</li><li value="5">CWIS should be accessible and should communicate properly in 2.4 GHz frequency mixed mode and job should be printed successfully in STEP 13.</li></ol>

RESOURCE_HW:

MDATE: 1683120867

APPROVED_SPAR:

TEST_CASE_TYPE: sanity

TC_WORK_LOCATION_CAT: work_from_office_tc

AUTHOR: q3SJKS2P

GROUP:

MUSER: q3SJKS2P

SPEC_TAG: [55.050.110.01] (FT-21767, FT-21093) {CS 1.0, DY 5.1} 2.4 GHz (2.4000 - 2.4835 GHz):

SPEC_NUM:

PROCEDURE: <p></p>
<ol><li value="1">Do the below configurations In Router/AP and save the changes<br />
&nbsp;&nbsp;&nbsp;&nbsp;- Give two different names for 2.4 GHz and 5 GHz frequency bands (i.e. ASUS-2G and ASUS-5G)<br />
&nbsp;&nbsp;&nbsp;&nbsp;- Configure the Router's/AP's Wi-Fi mode as IEEE 802.11b.<br />
&nbsp;&nbsp;&nbsp;&nbsp;- Configure the Router's/AP's frequency band as 2.4 GHz.<br />
</li><li value="2">Insert the Xerox Wireless USB Adapter (which supports 2.4 GHz and 5 GHz frequency bands and Wi-Fi modes) into the MFD's rear USB port.<br />
</li><li value="3">LUI will display a pop up that prompts the user to select either "Continue wireless install" or "Skip wireless setup".<br />
</li><li value="4">Click on "Continue wireless install" which will display the available networks.<br />
</li><li value="5">Select the SSID of the corresponding wireless AP ((i.e. ASUS-2G ) and enter the valid configurations (which should match the configurations applied in router and server) and save the changes by clicking on "Done" button.<br />
</li><li value="6">Join the network and Fetch the device new IP address from LUI or console and access the device CWIS using the new IP.<br />
</li><li value="7">Check whether the CWIS is accessible and communicating properly in 2.4 GHz frequency with IEEE 802.11b mode and Send a print job to confirm connection.<br />
</li><li value="8">Remove the Xerox Wireless USB Adapter Switch the device back to wired and Reconfigure the Router's/AP's Wi-Fi mode as IEEE 802.11g for 2.4 GHz frequency band and repeat step 2-7.<br />
</li><li value="9">Check whether the CWIS is accessible and communicating properly in 2.4 GHz frequency with IEEE 802.11g mode. and Send a print job to confirm the connection.<br />
</li><li value="10">Remove the Xerox Wireless USB Adapter Switch the device back to wired and Reconfigure the Router's/AP's Wi-Fi mode as IEEE 802.11n for 2.4 GHz frequency band and repeat step 2-7.<br />
</li><li value="11">Check whether the CWIS is accessible and communicating properly in 2.4 GHz frequency with IEEE 802.11n mode and Send a print job to confirm connection.<br />
</li><li value="12">Remove the Xerox Wireless USB Adapter Switch the device back to wired and Reconfigure the Router's/AP's Wi-Fi mode as Mixed Mode for 2.4 GHz frequency band and repeat step 2-7.<br />
</li><li value="13">Check whether the CWIS is accessible and communicating properly in 2.4 GHz frequency mixed mode and Send a print job to confirm connection.</li></ol>

DEVELOPMENT_COMPLETE_TIME:

ATM_LOCKED: 0

PRECONDITION_TO_BE_DONE:

PO_SIGNOFF_DATE:

APPROVE_SPAR:

RELEASE:

TESTCASE_PRODUCT:

FILENAME:

ATM_MCOMMENTS: Copied from "WFAST_Discovery_Regression_Connectivity/Testcases/FS_55.050_Wireless_Connectivity/18779".

RESOURCE_MEDIA:

COMMONALITY_DETAILS:

PRIORITY:

COMMON_FUNCTIONALITY:

APPROVED_QE:

TESTCASE_HEADLINE: To verify that Xerox Wireless adapter shall support the 2.4 GHz frequency band and its below Wi-Fi modes:
-IEEE 802.11b
-IEEE 802.11g
-IEEE 802.11n
-Mixed mode
(Validation from LUI)

TESTCASE_VERSION:

FEATURE:

APPROVE_SE:

SPEC_VERSION: 4.0042

TESTCASE_PLATFORM:

FILEDESC:

PROCESS:

TC_WEIGHTAGE:

COMPLEXITY_OUTPUT_VALIDATION: non_outliers

SKILL_SET:

TESTCASE_SOURCE:

APPROVE_QE:

COMPLEXITY_PRECONDITIONS: 0

TESTCASE_STEPS_ARE_RELATED_TO:

APPROVED_SE:

PLANNEDTIMESTAFF:

ATM_OWNER:

LOE:

ASSOCIATED_TESTCASES:

TRAINING:

ATM_REQLINK: 4035A80A-C920-11E7-A8DD-46D2A5FB8F22, 4041C0CC-C920-11E7-A8DD-46D2A5FB8F22, 40452A28-C920-11E7-A8DD-46D2A5FB8F22, 40473D0E-C920-11E7-A8DD-46D2A5FB8F22, 40495EAE-C920-11E7-A8DD-46D2A5FB8F22, 404BF970-C920-11E7-A8DD-46D2A5FB8F22

DEVICE_CATEGORY: common

SUB_FEATURE:

RESOURCE_CONSUMEABLES:

AUTOMATION_TC_VALIDATION:

QA_TEAM:

ATM_ID: 9C68933E-7F9F-11EF-8A42-99F16D3DB5FC

APTEST_UPDATE_STATUS: no

ATM_REQCOUNT: 6

COMPETENCY: wfast_connectivity

APTEST_TRACKING: yes

AUTOMATION_CANDIDATE: yes