ATM_ID: 8E60ABDE-6C87-11F0-962F-30CFC0ACCDE0

MFF:

PLANNEDTIMESTAFF:

ID: ETL/Copy_Print_Testcases/165605

TESTCASE_HEADLINE: COPY - Scale-COP-17216

GROUP:

FEATURE:

SUB_FEATURE:

INPUT: This test case will verify the UI behavior of Scale settings available in COPY screen

PROCEDURE: NOTE: For any UI specific changes/modifications please check the UI Documentation. It is important to view the design documentation during test execution to make sure any recent UI changes are verified.
 Link for Settings Behavior
 • Go to COPY
 • On the Copy Landing screen verify that Scale is an option on the Workflow Settings list
 • Press Scale and verify that the drawer will open from the right side
 • Verify the screen appears similar to the following
 7 screen
 
 4.3 screen
 
 
 
 **For the meantime%2c pls. refer to Settings Behavior
 • Verify that the default value for Scale Enter Value is Auto (100 depending on the current Copy From/To values.)
 • Press Enter a Value entry field
 • Verify the correct Numpad is shown on the screen where the user can enter an appropriate value within the setting s range
 • Verify the value range of Scale is 25 400. Minimum value is 25 and maximum value is 400. 
 • Verify when entered value is outside the range of the acceptable value then OK is pressed%2c it displays a Toast message Invalid entry. Value must be from 25 to 400. 
 • Verify hard numpad buttons also work. Pressing the hard keys should act the same as the soft keys
 • Verify hard Delete button removes the entered number when pressed.
 • Verify pressing plus sign (+) increments and minus sign (-) decrements current value by 1
 • Input any non-default value
 • Verify entered value is saved once OK button is pressed.
 • Verify under Workflow Settings List saved value is shown under Scale 
 • Verify Dynamic image on the right should show the corresponding image of the current Scale value.
 • Verify during the Grayed out state%2c the scale value is Auto 
 Note: When Copy To or Copy From paper size is changed from default%2c Scale is reassessed to show the appropriate value and state for the new combination. 
 • On the Copy screen%2c press value area of Copy To to make Copy To settings list show up
 • On the Copy To screen%2c select Auto Size Match
 • Press the value area of Copy To to close the Copy To window
 • Verify the Scale in Workflow Setting List is set to Auto without a percentage value.
 • Verify when Scale is selected%2c the Scale drawer screen is locked.
 • Select other value for Copy To (i%2ce Manual Feeder)
 • On the Copy screen%2c verify Scale value is NOT grayed out
 • Verify the Scale value is Auto (n) 
 • On the Copy screen%2c press value button of Copy From to make Copy From settings list show up
 • On the Copy From screen%2c select Auto Size Sense or Mixed Sizes
 • On the Copy To screen%2c verify value becomes Auto Size Match
 • Close the Copy From settings list
 • Verify the Scale value is Grayed out and set to Auto 
 • Select other value for Copy From. (i.e. A4%2c A5%2c Legal%2c B4%2c A3)
 • On the Copy screen%2c verify Scale value is Grayed out
 • Verify Copy To is still set to Auto Size Match
 • Select other value (Not Auto Size Match ) for Copy To
 • On the Copy Options screen%2c verify Scale value is NOT grayed out 
 • Verify the Scale value is equivalent to the expected Value of Copy From and Copy To (i.e 95 )
 • Press Back button
 • Verify Scale drawer is closed and returns to Copy Landing screen
 • Verify that by pressing the Back button is the only way to exit from the Scale drawer screen.
 
 Scale Presets
 • Verify under Enter a value is Presets 
 • Verify the following values are available and selectable
 o 50%
 o 75%
 o 100%
 o 125%
 o 150%
 o 200%
 • Verify default value is 100%
 • Verify if the value of Scale Enter a value match the value available in Presets then that value should be highlighted or in pressed state. 
 • Verify after pressing the Preset icon%2c the value should be displayed too in the Scale - Enter a value 
 • Touching and pressing one icons puts other icons in available state
 • Verify when 50% is touched%2c 50% is in pressed state. 
 • Verify when 75 % is touched%2c 75% is in pressed state and so on.
 • Verify only one icon should be selected at a time. 
 
 Note:
 • When scaling up%2c the area which is scaled should be determined by the original point. Remember that Flatbed scans are face down 
 • When some settings are enabled%2c scale cannot be adjusted. If the value for scale is known%2c the current value should be shown but the controls are unavailable. If the value for scale cannot be determined before the scan%2c the controls should be locked and the disabled settings text box is shown. The design for these behaviors can be found in the unavailable behaviors section.
 Information about modifications and conflicts can be found in the Conflicts and Modifications document.

TEST_COVERED_BY:

SRT_ANALYZATION:

OUTPUT: Expectation already stated in steps.

PROCESS:

PRIORITY:

TEST_TYPE:

LOE:

RESOURCE_HW:

RESOURCE_CONSUMEABLES:

RESOURCE_MEDIA:

SKILL_SET:

TEST_CASE_TYPE:

TESTCASE_SOURCE:

SPEC:

SPEC_NUM:

SPEC_VERSION:

SPEC_TAG:

ATM_OWNER:

APPROVE_QE:

APPROVED_QE:

APPROVE_SE:

APPROVED_SE:

APPROVE_SPAR:

APPROVED_SPAR:

ASSOCIATED_TESTCASES:

TRAINING:

TESTCASE_VERSION:

TESTCASE_STATE:

TESTCASE_PLATFORM:

TESTCASE_PRODUCT:

TESTCASE_FAMILY:

TESTCASE_APPROVALS:

CDATE: 1753798991

MDATE: 1753798991

MUSER: w4zfpb7v

AUTHOR: w4zfpb7v

ATM_MCOMMENTS: Imported from spreadsheet

HISTORY:

ATM_LOCKED:

ATM_REQLINK:

ATM_REQCOUNT: 0

QA_TEAM:

TC_WEIGHTAGE:

FILENAME:

FILEDESC:

FILES:

RELEASE:

COMPETENCY:

AUTOMATION_GROUP:

TESTCASE_STEPS_ARE_RELATED_TO:

REASON_FOR_AUTOMATABLE:

PRECONDITION_TO_BE_DONE:

ACTION_TO_BE_DONE:

COMMON_FUNCTIONALITY:

COMMONALITY_DETAILS:

CONSTRAINTS_DAR:

DEVELOPMENT_COMPLETE_TIME:

PO_SIGNOFF_DATE:

COMPLEXITY_PRECONDITIONS:

COMPLEXITY_OUTPUT_VALIDATION:

AUTOMATABLE:

AUTOMATION_CANDIDATE:

TESTCASE_MODIFICATION_REQUIRED:

APTEST_UPDATE_STATUS:

DEVICE_CATEGORY:

TC_WORK_LOCATION_CAT:

AUTOMATION_TC_VALIDATION: